2nd0508.fm Page0 Tuesday,M ay8,2001 10:18AM
2nd0508.fm Page2 Tuesday,M ay8,2001 10:18AM
Verifying Installation
Technical Specifications
When power has been applied to the switch:
Type
Specification
•
•
The green Pwr (power) LED on the front panel is on.
The green Link LED on each connected port is on.
ISO/IEC 802-3 (ANSI/IEEE 802.3i) 10BASE-T
Ethernet
IEEE 802.3u,100BASE-TX Fast Ethernet
compatible with major network software,
including Windows® networking, NetWare, and
Linux
Standards
Compatibility
When the switch is connected and operating, refer to the table in
“LEDs” for information about the LEDs and their activity.
Troubleshooting Information
100 Mbps with 4B/5B encoding and MLT-3
physical interface for 100BASE-TX
10 or 100 Mbps half-duplex
Data Rate
20 or 200 Mbps full-duplex
Symptom
Cause
Solution
RJ-45 connector for 10BASE-T or 100BASE-TX
Ethernet interface
Network Interface
Power
10M or 100M Port
Make sure the attached device is
7.5 w max
7.5 v DC input
Link LED is
off on a
connection powered and there is a proper UTP
is not
functioning.
connection.
connected
port.
Make sure the network adapter card
installed in the PC is working. Verify that
the network adapter card is operating at
the proper speed (10 Mbps or
100 Mbps).
Physical Specifications
Dimensions:
9.27 x 1.06 x 4.1 in.
23.0 x 2.7 x 10.3 cm
Make sure the proper cable is installed.
Check for miswired cable pairs or loose
connectors.
Weight:
1.25 lb; 0.6 kg
Environmental Specifications
For 100 Mbps operation, only
Category 5 or better grade cable should
be used. For 10 Mbps operation,
Category 3 cable can be used.
Make sure the length of the UTP cable
from the switch to the device does not
exceed 328 feet (100 meters).
Operating
0 to 40° C (32 to 104° F)
temperature:
Operating
humidity:
90% maximum relative humidity,
noncondensing
CE mark, commercial; FCC Part 15, Class B;
EN 55 022 (CISPR 22), C-Tick
Electromagnetic
Compliance
Green 100M Port is
Make sure the adapter card is capable of
and set for 100 Mbps operation if it is not
in 10 Mbps auto-sensing.
CE mark, Commercial
UL listed (UL 1950)
LED is off
when
operating
Safety Agency
Approvals for the
Power Adapter
operating in
a Fast
mode.
Ethernet
network.
Performance Specifications
14,800 frames/sec max for 10M port
148,800 frames/sec max for 100M port
Frame filter rate:
Green Link
Port is
Make sure the connected device is
10M or 100M operating in capable of full-duplex transmission,
LED is on
and Green
FDX LED is
off when
connected to
a full-duplex
network.
half-duplex using auto-sensing. The Model FS105
mode.
14,800 frames/sec max for 10M port
148,800 frames/sec max for 100M port
Frame forward
rate:
switch will not support a full-duplex link
that is not advertised using
auto-sensing.
10 Mbps to 10 Mbps: 70 µs max
10 Mbps to 100 Mbps: 40 µs max
100 Mbps to 10 Mbps: 60 µs max
100 Mbps to 100 Mbps: 70 µs max
Network latency
(using 64-byte
packets):
Yellow
Data
The port and switch might be functioning
correctly. However, check the following
to make sure that excessive collisions
4000 MAC addresses
Address
database size:
CollisionLED collision is
is blinking
excessively.
occurring
on the port. are normal (as in most Ethernet
networks) and not caused by:
Incorrect cabling or connectors
Wiring techniques
48-bit MAC address
256 kilobytes
Addressing:
Queue buffer:
Mismatched duplex operating mode
settings
© 2001 by NETGEAR, Inc. All rights reserved.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Trademarks
NETGEAR is a registered trademarks of NETGEAR, Inc. in the United States and in other
countries. Microsoft, Windows, and Windows NT are registered trademarks of Microsoft
Corporation. All other trademarks and registered trademarks are the properties of their
respective owners. All rights reserved. Information subject to change without notice.
Statement of Conditions
In the interest of improving internal design, operational function, and/or reliability,
NETGEAR reserves the right to make changes to the product described in this document
without notice.
NETGEAR does not assume any liability that may occur due to the use or application of
the product(s) or circuit layout(s) described herein.
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Certificate of the Manufacturer/Importer
•
Consult the dealer or an experienced radio/TV technician for help.
It is hereby certified that the NETGEAR Model FS105 Fast Ethernet Switch has been
suppressed in accordance with the conditions set out in the BMPT-AmtsblVfg 243/1991
and Vfg 46/1992. The operation of some equipment (for example, test transmitters) in
accordance with the regulations may, however, be subject to certain restrictions. Please
refer to the notes in the operating instructions.
Federal Office for Telecommunications Approvals has been notified of the placing of this
equipment on the market and has been granted the right to test the series for compliance
with the regulations.
EN 55 022 Declaration of Conformance
This is to certify that the NETGEAR Model FS105 Fast Ethernet Switch is shielded
against the generation of radio interference in accordance with the application of Council
Directive 89/336/EEC, Article 4a. Conformity is declared by the application of EN 55 022
Class B (CISPR 22).
Canadian Department of Communications Radio Interference Regulations
This digital apparatus (NETGEAR Model FS105 Fast Ethernet Switch) does not exceed
the Class B limits for radio-noise emissions from digital apparatus as set out in the Radio
Interference Regulations of the Canadian Department of Communications.
Federal Communications Commission (FCC) Compliance Notice:
Radio Frequency Notice
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
Règlement sur le brouillage radioélectrique du ministère des
Communications
Cet appareil numérique (NETGEAR Model FS105 Fast Ethernet Switch) respecte les
limites de bruits radioélectriques visant les appareils numériques de classe A prescrites
dans le Règlement sur le brouillage radioélectrique du ministère des Communications du
Canada.
•
•
This device may not cause harmful interference.
This device must accept any interference received, including interference that may
cause undesired operation.
2
|